34 Degree D Head Paper Strip Nails Galvanized Framing Nails for Nail Gun Wood Construction
plastic strip framing nails
* For use in 30 to 34 degree paper tape collation framing nailers
* Plastic tape collated smooth shank
* Electro Galvanized offers some corrosion protection.
* Hot dip galvanized coating resists corrosion and rust. For interior and exterior use. Rated for use in treated lumber.
* Bright finish for interior use in non-treated lumber only.
* Clipped Head, Offset Round Head.
Joist hanger framing nails is used to connect joist hangers to the joists or wood studs they will be supporting. Joist hanger nails are short and heavy gauge nails, providing increased holding power without fully penetrating the wood. They have a high shear strength to resist forces that make a material's internal faces slide parallel past each other. Storms, and high winds can cause shear stress in materials. For these reasons, nails are recommended over screws for installing connectors to the decking framework as screws lack the needed shear strength to resist shear stress.
* 34 Degree Paper Collated Joist Hanger Nails
* Used in the hanging of metal hangers, seismic, anchors and connector straps.
* 34-degree paper tape collated nail.
* Head-stamped for ease of identification.
* Full round head.
* Electro Galvanized fasteners have a very thin layer of Zinc that offers some corrosion protection.
* These nails are manufactured and collated to strict quality standards to ensure optimal performance in any of our varied styles of Metal Connector tools.
Shank Typez:
Smooth Shank:
Smooth shank nails are the most common and are often used for framing and general construction applications. They offer enough holding power for most everyday use.
Ring Shank:
Ring shank nails offer superior holding power over smooth shank nails because the wood fills in the crevasse of the rings and also provide friction to help prevent the nail from backing out over time. A ring shank nail is often used in softer types of wood where splitting is not an issue.
Screw Shank:
A screw shank nail is generally used in hard woods to prevent the wood from splitting while the fastener is being driven. The fastener spins while being driven (like a screw) which creates a tight groove that makes the fastener less likely to back out.
Annular Thread Shank:
Annular thread is very similar to a ring shank except the rings are externally beveled which presses against the wood or sheet rock to prevent the fastener from backing out.
Finishing:
Bright Finish:
Bright fasteners have no coating to protect the steel and are susceptible to corrosion if exposed to high humidity or water. They are not recommended for exterior use or in treated lumber, and only for interior applications where no corrosion protection is needed. Bright fasteners are often used for interior framing, trim and finish applications.
Hot Dip Galvanized (HDG):
Hot dip galvanized fasteners are coated with a layer of Zinc to help protect the steel from corroding. Although hot dip galvanized fasteners will corrode over time as the coating wears, they are generally good for the lifetime of the application. Hot dip galvanized fasteners are generally used for outdoor applications where the fastener is exposed to daily weather conditions such as rain and snow. Areas near the coasts where the salt content in rain water is much higher, should consider Stainless Steel fasteners as salt accelerates the deterioration of the galvanization and will accelerate corrosion.
Electro Galvanized (EG):
Electro Galvanized fasteners have a very thin layer of Zinc that offers some corrosion protection. They are generally used in areas where minimal corrosion protection is needed such as bathrooms, kitchens and other areas that are susceptible to some water or humidity. Roofing nails are electro galvanized because they are generally replaced before the fastener begins to wear and are not exposed to harsh weather conditions if installed properly. Areas near the coasts where salt content in rain water is higher should consider a Hot Dip Galvanized or Stainless Steel fastener.
Product Parameters
|
Material
|
Q195, Q235, stainless steel
|
|
Surface Finish
|
Bright, Galvanized, Hot Dipped Galvaized, Electro Galvanized, Zic Yellow, Zine Bule, MG, Dacro, etc.
|
|
Type
|
Paper collated, plastic collated and wire weld collated
|
|
Nail head
|
Smooth, Chequered, Convex, Roofing, Philips, Pozi, Square, Torx, etc
|
|
Nail Point
|
Diamond, Blunt, Chisel, Clinch, Shear, etc.
|
|
Nail Diameter
|
2.87-4.5mm
|
|
Length
|
50-130mm
|
Our Advantages
Company Profile
FAQ
Q1:Can I get a sample before i place an order?
Samples are available on most items.You can request a sample by contacting a sales representative , After you approve the sample , you could start ordering
Q2:What methods of payment do you accept?
We Accept T/T,L/C AT Sight, Western Union, Paypal , Visa,Master Card,Trade Assurance
Q3:How long will it take for my order to arrive?
Orders generally arrive within 20-30 business days by Sea After we ship out, It will depend upon where you are from. Most orders ship within 25days
Q4:Do you sell in small quantities
Generally for standard parts we accept small orders , but for Non-standard items , it will require a minimum quantity
Q5:How do you ensure the quality of your products?
Our quality system is compliant with the standards of ISO9001. All of our locations adhere to each of these requirements. The product we supply meets all applicable ISO DIN GB,ANSI,ASTM, JIS,BS specifications,And all the products will be inspected before shipping
Q6:Can you do OEM orders or do my brand packing for the fasteners
Yes , we can do OEM ,ODM orders and can do branded packaging
Q7:Can you develop non-standard fasteners and customized sizes
Yes , we support customized fasteners , just provide your specifications and requirements
){kind=link}